2001 Subaru Legacy L How to Remove and Install Front Suspension
download
Removal 1. Disconnect ground cable from battery. 2. Jack-up vehicle, support it with safety stands, and remove front wheels. 3. Unlock axle nut. See Fig. 9 . CAUTION: Be sure to loose and retighten axle nut after removing wheel from vehicle. Failure to follow this rule may damage wheel bearings. 4. 5. 6. 7. Remove axle nut while depressing brake pedal to prevent front drive shaft from turning. Remove stabilizer link. See Fig. 10 . Remove disc brake caliper from housing, and suspend it from strut using a wire. Remove disc rotor from hub. See Fig. 11 . If disc rotor seizes up within hub, drive disc rotor out by installing an 8-mm bolt in screw hole on the rotor. Remove cotter pin and castle nut which secure tie-rod end to housing knuckle arm. See Fig. 12 . Using a puller, remove tie-rod ball joint from knuckle arm. See Fig. 13 . Remove ABS sensor assembly and harness. See Fig. 14 . Remove bolt which secures sensor harness to strut. See Fig. 15 .
Removal 1. Disconnect ground cable from battery. 2. Jack-up vehicle, support it with safety stands, and remove front wheels. 3. Unlock axle nut. See Fig. 9 . CAUTION: Be sure to loose and retighten axle nut after removing wheel from vehicle. Failure to follow this rule may damage wheel bearings. 4. 5. 6. 7. Remove axle nut while depressing brake pedal to prevent front drive shaft from turning. Remove stabilizer link. See Fig. 10 . Remove disc brake caliper from housing, and suspend it from strut using a wire. Remove disc rotor from hub. See Fig. 11 . If disc rotor seizes up within hub, drive disc rotor out by installing an 8-mm bolt in screw hole on the rotor. Remove cotter pin and castle nut which secure tie-rod end to housing knuckle arm. See Fig. 12 . Using a puller, remove tie-rod ball joint from knuckle arm. See Fig. 13 . Remove ABS sensor assembly and harness. See Fig. 14 . Remove bolt which secures sensor harness to strut. See Fig. 15 .
Remove transverse link ball joint from housing. See Fig. 16 . 8. 9. 10. 11. 12. CAUTION: DO NOT pull inner joint when removing axle shaft. 13. Remove inner joint from transmission spindle. 14. Remove front axle
shaft assembly from hub. See Fig. 17 . 15. After scribing an alignment
mark on camber adjusting bolt head, remove bolts which connect housing
and strut, and disconnect housing from strut. See Fig. 18 . Removal 1. Disconnect ground cable from battery. 2. Jack-up vehicle, support it with safety stands, and remove front wheels. 3. Unlock axle nut. See Fig. 9 . CAUTION: Be sure to loose and retighten axle nut after removing wheel from vehicle. Failure to follow this rule may damage wheel bearings. 4. 5. 6. 7. Remove axle nut while depressing brake pedal to prevent front drive shaft from turning. Remove stabilizer link. See Fig.
10 . Remove disc brake caliper from housing, and suspend it from
strut using a wire. Remove disc rotor from hub. See Fig. 11 . If disc
rotor seizes up within hub, drive disc rotor out by installing an 8-mm bolt in screw hole
on the rotor. Remove cotter pin and castle nut which secure tie-rod end
to housing knuckle arm. See Fig. 12 . Using a puller, remove tie-rod
ball joint from knuckle arm. See Fig. 13 . Remove ABS sensor assembly
and harness. See Fig. 14 . Remove bolt which secures sensor harness to
strut. See Fig. 15 . Remove transverse link ball joint from housing. See
Fig. 16 . 8. 9. 10. 11. 12. CAUTION: DO NOT pull inner joint when
removing axle shaft. 13. Remove inner joint from transmission spindle.
14. Remove front axle shaft assembly from hub. See Fig. 17 . 15. After
scribing an alignment mark on camber adjusting bolt head, remove bolts
which connect housing and strut, and disconnect housing from strut. See Fig. 18 .
No comments:
Post a Comment